Common Types of Titanium Pipe Fittings - An Introduction
Overview
Titanium pipe fittings are connection and direction-change components fabricated from commercially pure titanium (Grades 1–4, e.g., TA1/TA2) or titanium alloys (e.g., Ti-6Al-4V), used to join pipe sections, change flow direction, reduce or branch pipeline sizes, and seal or service piping systems. They are widely applied in seawater systems, chemical processing, chlor-alkali plants, petrochemicals, shipbuilding, and desalination, where ordinary steel or stainless steel fittings would suffer chloride corrosion.
1. Butt-Weld Fittings (Welded Type)
These are welded directly to pipe ends and are the most common type for industrial, high-pressure, and large-diameter piping.
表格
| Type | Function / Description |
|---|---|
| Titanium Elbow (45° / 90° / 180°) | Changes flow direction. Available in long-radius (LR, 1.5D) and short-radius (SR, 1D) configurations per ASME B16.9. |
| Titanium Tee (Equal / Reducing) | Equal tees have three identical bores; reducing tees have one or two smaller branch outlets for branching pipelines. |
| Titanium Reducer (Concentric / Eccentric) | Connects pipes of different diameters. Concentric for vertical lines; eccentric (flat side up or down) for horizontal pump suction lines to avoid air pockets. |
| Titanium Cap | Welded to the end of a pipe to close/dead-end the line. |
| Titanium Stub End + Lap Joint Flange | The stub end is butt-welded to the pipe; the backing flange slides over it. Allows easy bolted disassembly and flange rotation during alignment. |
2. Threaded & Socket-Weld Fittings (Forged Type)
Smaller sizes (typically 1/8″–4″), forged from titanium bar or billet, complying with ASME B16.11.
Threaded Elbows / Tees / Crosses / Couplings / Caps - NPT or BSPT threaded; used in low-pressure instrumentation and utility lines.
Socket-Weld Elbows / Tees / Couplings - pipe is inserted into the socket and fillet-welded; provides stronger joints than threading for small-bore high-pressure lines.
Threaded Union / Half Coupling / Full Coupling / Bushings / Hex Nipples / Plugs - for compact, demountable small-pipe connections.
3. Flanged Fittings & Flanges
Flanges allow bolted, detachable joints - essential for valves, pumps, and vessels.
表格
| Flange Type | Typical Use |
|---|---|
| Weld Neck Flange (WN) | Butt-welded to pipe; high integrity, used in high-pressure/critical service |
| Slip-On Flange (SO) | Slides over pipe, fillet-welded both sides; economical, lower pressure |
| Blind Flange (BL) | Closes the end of a vessel or piping run |
| Threaded Flange (TH) | Screwed onto pipe; no welding, used where welding is impractical |
| Lap Joint Flange (LJ) | Used with titanium stub ends (see Section 1) |
| Socket Weld Flange (SW) | For small-bore, high-pressure piping |
| Plate Flange (PL) | Flat, welded to pipe; low-cost, low-pressure applications |
4. High-Purity / Sanitary Fittings
Used in pharmaceutical, food, semiconductor, and high-purity water systems - typically made from Grade 1 or Grade 2 titanium with electropolished surfaces.
Tri-Clamp (Tri-Clover) Ferrules - quick-clamp sanitary connections
Sanitary Elbows, Tees, Reducers, and Clamps - mirror-finished internal surfaces (Ra ≤ 0.4 μm), crevice-free designs
5. Specialty & Custom Fittings
Titanium Bends (Induction/Coated bends, 3D/5D/10D) - large-radius bends for pipelines requiring low flow resistance
Titanium Manifolds / Header Pipes - multi-outlet distribution headers for seawater or chemical systems
Titanium Spool Pieces & Flange Adapters - prefabricated, weld-ready assemblies
Titanium Vacuum Fittings (KF/NW, CF flanges) - for vacuum and semiconductor process lines
6. Common Manufacturing Standards
表格
| Standard | Scope |
|---|---|
| ASME B16.9 | Factory-made butt-welded fittings (elbows, tees, reducers, caps) |
| ASME B16.11 | Forged threaded and socket-weld fittings |
| ASME B16.5 | Pipe flanges and flanged fittings |
| ASTM B363 | Seamless and welded titanium pipe fittings (the core product standard) |
| ASTM B381 | Titanium forgings (for forged fittings and flanges) |
| ASTM B861 / B862 | Seamless / welded titanium pipe (raw material) |
| GB/T 27684 | Chinese standard for titanium pipe fittings |
7. Key Selection Considerations
Material grade: Grade 2 (TA2) is the most common balance of strength and formability; Grade 1 for maximum ductility; alloy grades where higher strength is needed.
Joining method: match the fitting type to the piping system - butt-weld for permanent industrial lines; flanged or threaded for maintainable connections.
Corrosion environment: confirm the medium is within titanium's resistance envelope (excellent for chlorides/seawater; avoid dry chlorine and fluorides).
Certification: request mill test certificates (MTC), PMI testing, and for critical service, radiographic/ultrasonic inspection of welds.
Avoid galvanic corrosion: when bolting titanium flanges to stainless or carbon steel flanges, use insulating gaskets and sleeves.






