Differences Between TA1, TA2, and TC4 Titanium
Overview
TA1, TA2, and TC4 are Chinese (GB) designations for the three most widely used titanium materials. TA1 and TA2 belong to commercially pure titanium (CP-Ti), while TC4 is an α+β titanium alloy (equivalent to Grade 5 / Ti-6Al-4V). They differ fundamentally in composition, strength, and application.
表格
| Item | TA1 | TA2 | TC4 |
|---|---|---|---|
| Category | Commercially pure titanium | Commercially pure titanium | α+β titanium alloy |
| ASTM equivalent | Grade 1 | Grade 2 | Grade 5 (Ti-6Al-4V) |
| Composition | >99% Ti, very low interstitials | >99% Ti, slightly higher O/Fe | Ti + 6% Al + 4% V |
| Strength level | Lowest | Medium | Highest |
| Formability | Best | Good | Moderate |
| Cost | Low | Low–medium | High |
1. Composition & Classification
TA1 - Commercially Pure Titanium (Soft Grade)
Titanium ≥ 99.5%, with the lowest oxygen and iron content among commercial grades.
Single α-phase (hexagonal close-packed) structure.
The softest and most ductile grade of titanium.
TA2 - Commercially Pure Titanium (Standard Grade)
Same basic composition as TA1 but with slightly higher oxygen/iron content, which raises strength.
Still single α-phase; the most widely used CP grade - the "workhorse" of the titanium industry.
ASTM equivalent: Grade 2.
TC4 - Titanium Alloy (α+β Type)
Composition: Ti-6Al-4V - 5.5–6.75% aluminum (α-stabilizer) + 3.5–4.5% vanadium (β-stabilizer).
Two-phase structure: α phase + β phase (body-centered cubic), which enables heat treatment (solution + aging) to dramatically increase strength.
ASTM equivalent: Grade 5 - the most widely used titanium alloy in the world.
2. Mechanical Properties Comparison
表格
| Property | TA1 | TA2 | TC4 |
|---|---|---|---|
| Tensile strength (MPa) | ≥ 240–370 | ≥ 400–550 | ≥ 895–1,100 |
| Yield strength (MPa) | ≥ 170 | ≥ 275 | ≥ 825 |
| Elongation (%) | ≥ 30 | ≥ 25 | ≥ 10–14 |
| Hardness (HB) | ~100 | ~140 | ~330 |
| Density (g/cm³) | 4.51 | 4.51 | ~4.43 |
| Working temperature | ≤ 300 °C | ≤ 350 °C | ≤ 400–450 °C |
Key point: TC4 is roughly 2–3 times stronger than TA1/TA2, but with significantly lower ductility. TA1 is the most easily formed and welded; TC4 is more difficult to machine and form.
3. Physical & Chemical Properties
表格
| Property | TA1 / TA2 (CP Ti) | TC4 (Alloy) |
|---|---|---|
| Corrosion resistance | Excellent - outstanding in chlorides, seawater, oxidizing acids | Very good, but slightly lower than CP Ti in some reducing media |
| Biocompatibility | Superior - preferred for implants | Excellent (ELI version Grade 23 used for load-bearing implants) |
| Oxidation resistance | Good | Better at elevated temperatures |
| Thermal conductivity | ~17 W/(m·K) | ~6.7 W/(m·K) - poorer (harder to machine) |
| Elastic modulus | ~110 GPa | ~114 GPa |
4. Processing & Fabrication
表格
| Aspect | TA1 / TA2 | TC4 |
|---|---|---|
| Cold forming | Excellent (TA1 best) - deep drawing, spinning | Difficult - usually hot formed or annealed before forming |
| Welding | Easy; standard GTAW/TIG with argon shielding | Requires strict shielding; weld zone loses strength (no age-hardening response in welds) |
| Machining | Relatively easy for titanium | Difficult - low thermal conductivity, work hardening |
| Heat treatment | Annealing only (no strengthening effect) | Solution treatment + aging can boost strength ~20–30% |
| Forging temperature | ~750–850 °C | ~850–950 °C (α+β field) |
5. Typical Applications
TA1 - where maximum formability and corrosion resistance matter:
Deep-drawn chemical equipment (tanks, vessels)
Electroplating racks, anode baskets
Heat exchanger parts requiring severe forming
Medical/dental components needing maximum biocompatibility
TA2 - the general-purpose industrial grade:
Chemical reactors, pressure vessels, heat exchangers
Seawater piping systems, desalination equipment
Plating and anodizing industry components
Structural parts requiring welding + corrosion resistance
TC4 - where high strength is essential:
Aerospace: aircraft structural parts, engine components, landing gear
Medical: bone screws, joint prostheses (ELI version)
High-performance automotive and racing parts
High-pressure vessels, turbine components
Sports equipment (bicycle frames, golf clubs)
6. Cost Comparison
表格
| Grade | Relative Material Cost | Relative Fabrication Cost |
|---|---|---|
| TA1 | ~1× (baseline) | Low |
| TA2 | ~1–1.2× | Low |
| TC4 | ~3–5× | High (harder machining, heat treatment required) |
Summary - How to Choose
表格
| If you need... | Choose |
|---|---|
| Best formability, deep drawing, lowest strength | TA1 |
| Balanced strength, corrosion resistance, weldability, and cost (general industrial use) | TA2 |
| High strength-to-weight ratio, aerospace/medical/high-load applications | TC4 |
TA1 and TA2 are commercially pure titanium grades differing mainly in strength (TA2 is stronger due to higher oxygen content), while TC4 is a heat-treatable Ti-6Al-4V alloy offering two-to-three times the strength at the cost of formability, weldability, and price.










